Methanesulfonic acid type tin plating additive

Methanesulfonic acid type tin plating additive

Matte tin and tin-lead electroplating process

Product Code No. Sn-818

Description and characteristics

Sn-818 is a fluorine-free tin and tin-lead process that can be used for rack plating, barrel plating and continuous electroplating. In a wide current density range, a thin, fine, misty and uniform coating can be obtained.

Head record

1 . A solution composition ---- linked & Barrel  

B solution composition ---- Continuous Plating

2 . A built bath ---- linked & Barrel

B a bath ---- Continuous Plating

3 . Bathing procedure

4 . Operating conditions

5 . Solution maintenance

6 . Equipment & operating skills

7 . Analysis procedure

8 . safety warning

9 . Wastewater treatment

*The current density range will determine the actual tin-lead concentration. 

1. Add 1/2 of the volume of deionized water to the tank  

2. Add the required methanesulfonic acid and stir  

3. Add the required tin methanesulfonate and mix until uniform  

4. Warm up to operating temperature  

5. Add Sn-818A and mix thoroughly  

6. Replenish water to the operating level  

7. Add Sn-818B slowly and mix thoroughly  

Temperature 70-122 ℉ ( 21-50 ) is the best: 85 ℉ ( 29 ℃)             

The recommended ratio of anode and cathode is 1 : 1             

Anode current density 2 0AS F (maximum 2.0AS D )             

Cathode current density 0.9-46.3 ASF (0.1-5.0 ASD)             

Cathode stirring 3-6 ft/min (1-2m/min)             

Anode high purity tin, tin / lead, platinum titanium                    

Temperature . 9 0-1 40 deg.] F ( 32 - 60 deg.] C) optimum: 120-130 deg.] F ( 49-55 deg.] C)             

Recommended ratio of anode and cathode 2 : 1             

Anode current density 10 0 -800 AS F ( 10.8-86 AS D )             

Cathode stirring Strong solution agitation or cathode movement             

Anode high purity tin, tin / lead, platinum titanium

Tin methanesulfonate and methacrylic acid by partial chemical bath add analysis results.

 Sn-818A : is the initial grain micronizer, it will be consumed with electrolysis and carry-out, 150-300 ml per 1000 ampere hour      

 Sn-818B : Strengthen the dense structure of the coating to provide a smooth and dense coating. It is consumed with electrolysis, 10-30ml per 1000 ampere hour    

Trough

Need PP , PE , PVC or the same acid-resistant material lining, PP , PE welding tank is superior to PP , PE molding tank, because the mold release agent used for molding will cause irremediable pollution to the tank liquid. New tanks or used tanks should be cleaned as recommended. Before building a bath, contact Bigley for specific instructions.

filter

Using Dynel or PP cartridge, 10 [mu] m , only non-filter in the bath for metal workpieces, filtered insufficient cause sintering or rough coating.

Heater

Quartz, Teflon or Teflon only on the surface

ventilation

Should have considerable exhaust capacity

anode

(It is recommended that soluble and insoluble anodes should not be mixed together)

Soluble anode

(The titanium basket is full at any time). The anode hook can be titanium or Monel , preferably with a plastic sheath. The anode hook cannot touch the bath. The anode bag should be made of Dynal or PP . If it is a used anode bag, It needs to be leached with 5% MSA solution first to remove large and small impurities.

Insoluble anode

Platinum titanium or iridium oxide film titanium, mainly used in high current density or spray application

Rectifier

Direct current, wave volt does not exceed 5%

And Bi Gelai contact representatives

For the sake of health and safety, Bigley recommends that manufacturers refer to Bigley's material safety data sheet before use .

Before treating wastewater according to Bigley 's wastewater treatment recommendations, users must understand the local / state / federal regulations that allow local or foreign treatment methods. If our recommendations conflict with regulations, local / state / federal regulations shall prevail.

FAQ

1. Q: Do you make the products yourself? Are you a trader or a manufacturer?

A: Yes, the products are produced by our company. Our company is a manufacturer focusing on the R&D and manufacturing of environmental protection electroplating additives. Our factory has 5000 square meters with an annual capacity of 15000 tons.

2. Q: Can your company send samples for trial?

A: We can provide samples for trial.

3. Q: What is the quality of your products?

A: Our company all products core raw materials is used by Germany BASF, American Dow Chemical and other international brand products. The production process is strictly in accordance with the ISO9001 quality management system, from the incoming inspection, product inspection, according to the strict inspection standard, ensure that every drop of products qualified. Product quality you can rest assured, like BYD, Huawei, Foxconn such enterprises are also using our products.

4. Q: How long is the shelf life of your products?

A: The shelf life of our products is two years. If you do not use up the products within a short time after you buy them, we suggest you store them in a cool place, not in the sun or in a high temperature environment.

5. Q: Are your products environmentally safe?

A: Our products have passed the SGS test and are recognized as "Green and Environment-friendly Promotion Products". Many auto parts and electronic products which use our products can pass the strict environmental protection test when they are exported to Europe and America. Therefore, we can be trusted in terms of environmental protection and safety.

6. Q: Can your company provide technical services?

A: Yes, our company has a technical service team of more than 10 people. The technical engineers all have more than 20 years' experience in electroplating factory. They can provide customers with comprehensive technical of pre-sales and after sales.

7. Q: Is it possible to visit your company?

A: Yes, of course. You are very welcome! We can meet you at Jieyang airport, If you can come to our city. Also you can visit our factory through live video.

8. Q: Can you customize products according to our needs?

A: Yes, our company has research and development strength, the product formula derived from Europe and the United States laboratory, European and American engineers technical support, work together with domestic universities. Our company has a member of Guangdong province expert enterprise workstation, Shantou university science and technology correspondent workstation, Jieyang city environmental protection engineering research center for electroplating additive.Therefore, it can meet all kinds of customized requirements proposed by customers.